Cheap forklifts are generally used in construction sites or factories. In these two places, the possibility of working at high places cannot be avoided. Therefore, it is difficult for laborers to work at high places, and it will cost a lot to go up. Strength and equipment, if our cheap forklifts don’t have to work hard in the first place, this is more cost-effective, then some people say that the cheap forklifts they are watching are not high nor high, so let our electric forklift manufacturers give them We introduce how high our cheap forklifts can reach.
The larger adjustment height of cheap forklifts refers to the safe distance between the upper surface of the level section of the forklift and the road when the cheap forklifts are fully loaded and the goods are raised to the maximum position. According to electric forklift manufacturers, the standard gantry is a gantry with two sections with a maximum lifting height of 3 meters. This height basically meets the requirements of many operating heights. Therefore, the most common forklifts we see on the market have a lifting height of 3 meters. . The adjustment height of the truck fork is usually 210mm up and down. The height of the stacker forklift fork is generally about 4.8 meters. The adjustable height of the lift truck can be up to 11 meters long. According to the selection height, cheap forklifts can be divided into low-level forklifts (about 2.5 meters) and high-level forklifts (up to 10 meters). The low safety driving three-way palletizing forklift can be raised by 12 meters. High safety driving three-way palletizing forklift can raise the height by 14.5 meters.
cheap forklifts When the goods are shipped, the goods should be close to the storage shelves, and the height of the goods should not exceed the storage shelves, otherwise the goods are very easy to roll to the actual operating staff and damage the driver. Manipulating items on the plug has a balancing effect. Repair and report problems found immediately, never work with faults or conceal them.
For everyone's safety, you must do what you can when you use it. Don't be too anxious and stack too high, but it will outweigh the gains. This will not bring much benefit to our operators. We must protect our own safety.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
