Common faults of electric forklift manufacturers chinasmall electric forklift
The throttle valve in the forklift of electric forklift manufacturers china realizes the control of fluid flow by changing the throttle length or throttle section. The throttle check valve and the throttle valve in parallel can be combined into a one-way throttle valve. However, when we use the small electric forklift daily, the throttle valve will malfunction, which is a headache. So, let's analyze the failure of the throttle valve for everyone.
1. Common faults of electric forklift manufacturers chinasmall electric forklift throttle valve
1. The flow of the throttle valve is unstable and fluctuates from time to time
2. Little or no flow at the outlet of the small electric forklift throttle valve
3. Increased internal leakage flow
Two, electric forklift manufacturers china failure cause analysis and diagnosis and solutions
The flow of the throttle valve is unstable and fluctuates from time to time
reason:
The oil is mixed with impurities, which are adhered to the edge of the orifice, and the flow cross-section becomes smaller, which causes the flow rate to slow down; when the impurities in the oil are washed, the flow cross-section increases and the speed increases.
The temperature of the small electric forklift system rises, which causes the viscosity of the oil to decrease, thereby increasing the flow rate and speeding up.
The damping device is blocked, there is air mixing inside the system, pressure fluctuations and bounces occur, and the speed is unstable.
The internal and external leakage of the throttle valve is large, the flow loss is large, and the required flow cannot be guaranteed.
Diagnosis and solutions:
First disassemble and wash the throttle valve, clean the stains, and replace the filter. If the oil is seriously dirty, it is recommended to replace the oil.
Electric forklift manufacturers china believes that certain heat dissipation and cooling measures should be taken when necessary.
Check the gap between the valve core and the valve body. If the gap is too large, it is safer to replace the valve core.
Clean the throttle valve with damping device, check that the moisture of the exhaust device is working normally, if it is abnormal, repair and exhaust the air in the oil.
The small electric forklift throttle valve has no flow or very little flow at the oil outlet
reason:
The clearance between the valve core and the valve hole is too large, causing serious leakage.
The orifice is blocked and the valve core is stuck.
Diagnosis and solutions:
(1) Electric forklift manufacturers china recommends to find out if there is a serious leak first, find out the reason, and then prescribe the right medicine.
(2) The small electric forklift is disassembled and inspected, the orifice is cleaned, the oil is replaced, the filtering accuracy is improved, and the oil is kept clean.
(3) Check whether the gap between the valve hole and the valve core is too large. If it is too large, the valve core needs to be replaced.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
