The system of electric forklifts using this steering method is usually arranged on the left side of the forklift, with the front connected to the frame and the rear connected to the driving device. It mainly consists of the steering wheel, steering shaft, connecting rubber pad, chain seat assembly, chain, large sprocket, and the rotating part of the driving device. During its operation, the steering wheel is rotated through the steering shaft, connecting rubber pads, and the small and large wheels in the chain seat drive the small sprocket to rotate. The chain also drives the large sprocket to rotate and the driving device to rotate, causing the driving wheel to deflect and achieve vehicle steering. Early small electric forklifts mostly used this steering type.
The steering system of a battery tractor is a front wheel (single wheel) steering system. The system mainly consists of steering wheel, steering shaft, steering gearbox, and front wheel assembly.
The structure of the electric forklift steering system is: the upper end of the steering shaft is connected to the steering wheel, and the lower end is connected to the small gear in the steering gearbox. The small gear is combined with the bridge gear. The bridge wheel also fits with the large gear. Machine a 149 arc groove on the lower end face of the large gear and limit the maximum turning angle through a limit pin. The function of the bridge gear is to align the direction of the steering wheel and the steering wheel. The function of the steering system steering gearbox is to amplify the force exerted by the driver on the square wheel (at a magnification of 2.9 times) and slow down the driver.
When the driver turns the steering wheel, the steering shaft and small gear rotate together, passing through the bridge gear, driving the large gear and its fixed axle fork shaft to rotate. The steering wheel is installed on the axle fork shaft, and it also rotates at a certain angle to achieve this.
The steering of electric forklift vehicles is connected to the steering shaft, fork shaft, and box through various bearings, and there are also bearings inside the axle wheels. These bearings and gears are lubricated with calcium based grease. Therefore, sufficient lubrication should be provided during maintenance and repair assembly.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
