How are the electric stacker components installed?
In the warehouse workshop, the application of electric stacker is becoming more and more popular. When bosses buy electric stackers from electric forklift manufacturers, for the consideration of transportation space and safety, they are often not finished products, and some parts need to be installed by themselves. Then, the installation of electric stacker has become a very important problem. Let's follow us to understand the principle and steps of the installation of electric stacker parts.
The installation of electric stacker usually follows the installation principles from bottom to top, from inside to outside, from rear to front and from left to right. Let's take a look at the specific steps:
The piston ring shall be used in a complete set and cannot be disassembled at will. Install from the third ring.
Do not touch the piston, crankshaft bushing surface, connecting rod, piston, crankshaft and camshaft at will. The installation of these parts must be evenly oiled to protect and lubricate them.
Grease the O-ring as required and install the cylinder liner. Remind everyone not to knock the cylinder liner during installation.
Remember not to install the ring vertically or horizontally. When installing the ring mouth, it is advisable to stagger at least 120 °.
Electric forklift manufacturers usually require customers to install cylinder gasket after oiling. This process is irreversible.
When installing the cylinder head screws, the wrench shall be tightened from the middle to the four sides for 2-3 times, tighten the cylinder head screws to ensure that each screw is stressed evenly, and then separate from the middle to both ends. Tighten the crankshaft bushing connecting rod 2-3 times.
Install the piston connecting rod in the original direction of the piston as required. Install the piston connecting rod with the special tool. In addition, do not knock the piston and apply the oil evenly to the connecting rod bushing.
When installing the high-pressure fuel injection pump gear and camshaft, pay attention to the alignment of the gear. The above are the principles and steps for electric forklift manufacturers to install electric and hydraulic forklift parts. I hope our content is helpful to you.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
