What are the common faults of the manual pallet jack?
The manual pallet jack has always been a very popular logistics storage equipment, with low price, wide application range, small size and convenient use. However, although the manual pallet jack is simple in structure and easy to maintenance, some failures are unavoidable. What faults are common and how to deal with them? The pallet jack manufacturer came to tell us about it.
First of all, let's talk about the oil pump, which is an important part of the manual pallet jack. How important is it? If there is a problem with the oil pump, the entire manual pallet jack can no longer work. There are many small parts in the oil pump, among which the dust ring, O-ring, steel ball are prone to problems. When encountering problems, we should check these parts first, and then eliminate them one by one. If any problem is found, the simplest solution is to replace the parts. The second is the oil cylinder. The oil cylinder is also very important for the manual pallet jack, which is mainly responsible for the lifting and lowering of goods. If the fork cannot be lifted or lowered, it may be due to the following reasons: overload or eccentric load; The piston rod is exposed for a long time, causing rust; The nut is misaligned. The pallet jack manufacturer told us that in case of this problem, we should find out the root cause first, and then replace the piston rod or oil cylinder and adjust the nut as the case may be.
Let's talk about the oil seal of the manual pallet jack. The oil seal is located between the piston rod and the cylinder barrel. The pallet jack of the pallet jack manufacturer uses imported oil seals, which have better sealing performance and wear resistance. If there is oil leakage, it is likely that the oil seal is aging. No matter how good the oil seal is, it has a lifetime. If the service life is long enough, it should be replaced in time. Finally, let's talk about the lever frame. It is a part used to connect the oil pump and the push rod. Only with it can the operation of the manual pallet jack reach a balanced state. The problems that may occur are usually deformation or fracture, which are usually caused by overload or eccentric load. The pallet jack manufacturer reminded that once the lever frame breaks, the operation must be stopped immediately and we must replace it as soon as possible. If the work continues, the goods may be damaged.
The manual pallet jack of the pallet jack manufacturer has the following unique advantages: thickened iron plate, stronger bearing capacity, and the fork is not easy to deform; The seam welded by the robot arm is firmer and has a long service life; The overall oil cylinder main pipe is 38.5mm, maintenance free, galvanized design, and more durable; The seal ring of the hydraulic cylinder is imported from Taiwan, which has the advantages of long service life and is more safe and durable. Welcome to consult us about the manual pallet jack.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
