Principles and steps for installing small electric forklift parts in electric
The application of small electric forklift is gradually popularized in the shelf rooms of workshops and warehouses. After we purchased the small electric forklift from electric forklift manufacturers china, because of the consideration of transportation space and safety, it is often not a finished product, and some parts need to be installed by yourself. Then, the installation problem of small electric forklift has become a very important issue. Next, follow us to understand the principles and steps of installing small electric forklift components.
The installation of small electric forklift usually follows the installation principle from bottom to top, from inside to outside, from back to front, and from left to right. Let's take a look at the specific steps:
1. The piston ring should be used as a complete set, and can not be disassembled and assembled at will. Start installation from the third ring.
2. Do not touch the piston, the surface of the crankshaft, the connecting rod, the piston, the crankshaft, the camshaft at will. When installing these parts, the oil must be evenly coated for the purpose of protection and lubrication.
3. Apply butter to the O-ring as required, and then install the cylinder liner. Electric forklift manufacturers china reminds everyone not to knock the cylinder liner during installation.
4. Remember not to install the ring in the vertical or horizontal direction of the small electric forklift. When installing the ring opening, it is appropriate to stagger at least 120°.
5. Electric forklift manufacturers china has another thing to tell you that the cylinder head gasket can be installed after the oil is applied, and the process is irreversible.
6. When installing the cylinder head screws, electric forklift manufacturers china should also remind everyone to pay attention. The wrench should be tightened from the middle to the four sides of the cylinder head screw in 2-3 times to ensure that each screw is evenly stressed, and then from the middle to the center. Tighten the connecting rod of the crankshaft bush in 2-3 times at both ends.
7. Install the piston connecting rod in the original direction of the piston as required, and use special tools to install the piston connecting rod. The piston cannot be knocked as well, and the oil must be evenly applied to the connecting rod bush.
8. Pay attention to the alignment of the gears when installing the high-pressure fuel injection pump gears and camshafts. Electric forklift manufacturers china believes this is very important.
The above are the principles and steps for installing small electric forklift parts in electric forklift manufacturers china. I hope our content can be helpful to everyone.
-
Breakthrough improvements in bucket tines and masts"We are a manufacturer specializing in the production of all kinds of standard forklifts and off-road vehicles. We produce a complete range of internal combustion forklift trucks, and they are very easy to use. In the following content, we will introduce the relevant knowledge of the product in detail, I hope it can be helpful to you when you use it.Do you like ?0
Read more -
New energy forklift power system controllerIn the electric forklift power unit, when the forward contactor is closed, the motor is in a forward rotation state; Whereas, when the reverse contactor is closed, the motor is reversed. By changing the direction of the armature current or excitation current, or by changing the polarity of the excitation winding, the commutation control of the motor is realized. However, the use of two sets of excitation windings with opposite windings will lead to a complex structure and an increase in the volume of the motor, so the first two methods are more commonly used in practicalDo you like ?0
Read more -
Electric forklifts vs. internal combustion forkliftsHowever, there are also some drawbacks to internal combustion forklifts. First of all, diesel engines are more expensive to run, especially against the backdrop of the current surge in oil prices. Secondly, the internal combustion forklift is noisy and vibrate, and the operating noise of the diesel engine has an irreversible impact on the human body. In addition, the exhaust gas pollution is serious, even if the processor is installed, it will cause environmental pollution, and it is necessary to clean up the dust regularly, which is more cumbersome to maintain, and can easily lead to oil pollution problems on the site.Do you like ?0
Read more -
What are the daily maintenance of electric forklifts?Electric forklifts are important equipment in warehousing and logistics operations, and regular maintenance is crucial. The following guide provides comprehensive recommendations for electric forklift maintenance:Do you like ?0
Read more -
"Electric Forklift Maintenance: Longer Life and More Efficiency"The above is a brief introduction to the maintenance work of electric forklifts, only the correct maintenance work can ensure the better operation of electric forklifts and improve work efficiency.Do you like ?0
Read more -
"Level 3 maintenance is indispensable! Forklift maintenance strategy"First, the key points of the first-level maintenance of forklifts Carefully check the engine oil quantity, oil viscosity and oil cleanliness; Thoroughly clean the battery and add distilled water if necessary to ensure performance; Examine the appearance and tightness of the fan belt; Check the gearbox, drive axle, working oil pump and water pump transmission device for abnormal noise; According to the regulations, add an appropriate amount of oil or grease to each part of the clutch and brake longitudinal link;Do you like ?0
Read more
